Insyde H2OFFT (Flash Firmware Tool) Release Notes

Version 200.02.00.02
------------
## Common
- Fix "Secure Flash failed when there is image buffer allocated by BIOS." [ITS##0086374]

Version 200.02.00.01
------------
## Common
- Prettify UI.
- Fix failed the commnad '-pq -all' can get protected address rather than 0.

Version 200.02.00.00
------------
## Common
- Add parameter-buffer based IHISI support.

Version 200.01.00.25
------------
## Common
- PFAT V3 support for full BIOS image.
- Update SecurityFlash package for Windows Capsule Update.

Version 200.01.00.24
------------
## Common
- '-rmc': Ignore digest data when comparing ROM map.

Version 200.01.00.23
------------
## Linux
- Fix 'Get segmentation fault when comparing ROM changes(-rmc)'.

Version 200.01.00.22
------------
## Common
- Give a default message of the delay of finishing flash

Version 200.01.00.21
------------
## Common
- Reduce H2OFFT memory usage

Version 200.01.00.20
------------
## Common
- Add new command '-rmc' for checking ROM map and remind the user of the layout is cheanged.
- Add new command '-y' to suppress the "Yes/No" question and make the selection to "Yes".
- Add new command '-delayexit:<second>' to delay flash utility termination after flashing BIOS completed.

Version 200.01.00.19
------------
## Common
- Fix the hang issue during direct flashing
- Remove rarely-used commands
## GUI
- Remind users of ticking region while selecting a protected area. [ITS##0063417]

Version 200.01.00.18
------------
## Common
- Remove the flash progress bar from the console
- Center the message while flashing BIOS.

Version 200.01.00.17
------------
## Linux
- Read file failed if flash full image (32MB). [ITS##0049543]
- It shows "Error: IHISI function is not supported. (10h)" while flash BIOS [ITS##0049369]
- Cannot close dialog by press “OK” button [ITS##0049886]
- Sign PFAT failed with SecurityFlash_x86_WIN_100.00.02.22 [ITS##0077345]
- Some [ReturnCodeDefinition] error code cannot work. [ITS##0048606]
- Error message is incorrect if sign bios guard image without -securebiosguard [ITS##0065182]
## DOS
- The screen stays for two minutes during secure flash process. [ITS##0049099]
- Type command ''-RH'',H2OFFT will pop up Error:IHISI failed (53h). [ITS##0037169]
## Windows
- Open file failed if test with [Multi_FD] flag=1 with single package [ITS##0040645]
- Only flash certain region but all regions flashed in GUI mode [ITS##0063417]
- Type argument ''-beep'',buzzer don't have beep sound during flash BIOS process. [ITS##0038694]

Version 200.01.00.16
------------
## Linux
- Show error message when load driver failed when SecureBoot is enabled.

Version 200.01.00.15
------------
## Common
- Add gcc3 compatible
- Fix Error message is not clear if enable PFAT feature [ITS##0058450]
## Linux
- Describe how to sign driver when secure boot enabled.

Version 200.01.00.14
------------
## Common
- Show ME version

Version 200.01.00.13
------------
## Common
- Fix Beep function for onboard speaker
- Update 
## Windows
- Support IHISI Security feature.
## GUI
- Add Option|Region page to specify regions individually


Version 200.01.00.12
------------
## Console
Fix typo "-slient" to "-silent"

Version 200.01.00.11
------------
## Linux
add -slient to mute stdout and stderr
## DOS
Unable to flash/dump BIOS when IHISI Security enabled.

Version 200.01.00.10
------------

## GUI
- fix missing icon in application menu.
- fix duplicate region warning message always show when SkipRegionCheck is On.
- Font problem in options interface on Ubuntu 20.04 [ITS##0072091]
## Common
- Can not flash ec region [ITS##0073575]
- fix UpdateEC flag is not work under secureflash
- Add Skip Region Check option
- Any argument can be executed on single package even if didn't enter any argument filter [ITS##0064310]
- Type command ''-RH'',H2OFFT will pop up Error:IHISI failed (53h). [ITS##0037169]

Version 200.01.00.09
------------

## GUI
- [H2OFFT_Linux64_200.01.00.08] Set [FlashComplete]Dialog=1 can not work success. [ITS##0073015]
- [H2OFFT_Linux64_200.01.00.07] Font problem in options interface on Ubuntu 20.04 [ITS##0072091]

Version 200.01.00.08
------------

## Common
- Update Secure Package to 100.00.02.20

Version 200.01.00.07
------------

## Bug Fix
- GUI didn’t pop up error message if FD file is not be setting in platform.ini [ITS##0071069]
- Address are are 0 with -pq parameter [ITS##0071164]
- iFdPacker failed while package mode is “Both Windows and DOS” [ITS#0071194]
- Tool didn’t be closed if pops up error message [ITS#0071213]
- GUI stops on initialization while [option] flag=0 in platform.ini [ITS#0071240]
- Failed to run “secure flash” [ITS#0071403]

Version 200.01.00.06
------------

## Bug Fix
- Fix tool crash (region index out of bound).
- Fix tool is able to flash BIOS even if BIOS image size is different than ROM report size.
- Fix It shows "Insyde H2OFFT-L 100.00.08.23" is not responding if flash BIOS on GUI mode [ITS#0048271]
## GUI
- Fix the BIOS info was overlapped by progress bar. [ITS#0049908]

## Feature
### Common
- Support Intel PFR feature.

Version 200.01.00.05
------------

## Bug Fix
- Unable to flash bios on ElkhartLake
- Fix Can't preserve OA3 key and variable when enable bios guard function [ITS#64434]

Version 200.01.00.04
------------

## Feature
### Common
- Fix BVDT did not update on AMD platform. 
- Update SecureFlash package [ITS#63448]

Version 200.01.00.03
------------

## Feature
### Common
- Update SecureFlash package to 100.00.02.15
- Support to specify ESP path in platform.ini
- Support to flash region id higher than 5
### Windows
- Add the Packer user guide.
### GUI
- Show version in property window.

## Bug Fix
- System can't flash system BIOS after enable BIOS guard. [ITS#57452]
- Packer: Unable to launch H2OFFT-GUI. [ITS#61978]

Version 200.01.00.02
------------

## Bug Fix:
### Common
- Fix flashing becomes slow.
- Fix tool always return the value of RETURN_NEED_REBOOT in platform.ini. [ITS#49172]
- Add delay reboot feature [For OEM/ODM]
- No model name and BIOS version while flash BIOS. [ITS#59972]

### Windows
- Stop loading the driver when the tool is ready to exit. [ITS#60684]

Version 200.01.00.01
------------

## Bug Fix:
Common
- Update SecureFlash package to 100.00.02.14
- Update Packer to 100.00.03.09 [ITS#56220]
- Fix the BIOS version won't be updated when there are two BVDT regions exist.
- Fix "-gbe parameter failed" [ITS#48272]
Windows
- Fix BSOD on CometLake platform [ITS#59457]
Windows/Linux
- Unload driver before reboot or shutdown.
GUI
- Show N/A when no Date in BIOS. [ITS#59099]

## Feature:
Common
- Support IHISI security mechanism.
- iFdPacker: Add "protect" feature. [ITS#53588]

## Enhancement:
DOS
- Show message when memory is not enough.


Version 200.01.00.00
------------
## Enhancement:
WINDOWS
- Refine the windows driver

Version 200.00.00.05
------------
## Bug Fix:
Common
- Fix issue that action_20 in UpdateEc in platform.ini is not working
- Remove incorrect return code which is only a warning not error.

Version 200.00.00.04
------------
## Bug Fix:
Common
- BUGFIX: Tool will stuck 20 minutes in long run.
- add argument "-rmp" description in help

## Enhancement:
Linux
- Add ability to override nmi_watchdog value. [For OEM/ODM]

Version 200.00.00.03
------------

## Bug fix:
WINDOWS
- Fix flash failed when using full image under CFL/CNL(32MB)
DOS
- Fix FFT crash on certain platfrom.

Version 200.00.00.02
------------

## Bug fix:
LINUX
- Fix flash failed when Secure Boot Enabled.
- Fix flash from ESP failed.
- Fix flash failed on GUI

Version 200.00.00.01
------------

## Feature:
COMMON
- Add Copper Point Support

Version 100.00.08.23
------------
COMMON
- Add new parameter "-cs:" to select which ROM would be flashed.

Version 100.00.08.22
------------
COMMON
- Flush the print buffer of progress bar.
- Update the signer version to 100.00.02.06
- Fix -e: command shows size does not match error message.

Windows
- Upgrade the Windows driver to 100.00.09.00

Version 100.00.08.21
------------
LINUX
- Fix the SMI command port search fail.

Version 100.00.08.20
------------
COMMON
- Auto Detect AMD/Intel Platform.
- Fix: Unsupport to flash secure BIOS which size larger than 64MB.
- Fix: The value of progress bar is incorrect.

Version 100.00.08.19
------------
COMMON
- Platform.ini support preserve dmi data.
- Update SecurityFlash_x86_WIN_100.00.02.04
- ACB => Show "System battery life percentage XX% < battery bound YY%".

WinPE
- Check battery status by OS API first.

Version 100.00.08.18
------------
LINUX
- Fix the all bits of IO port 61h will be cleared during flash bios.

Version 100.00.08.17
------------
COMMON
- Fix platform support both ESP and Memory secure flash at the same time Flash fail issue.
- Support Platform.ini [PermitFlashVersion]
- Update SecurityFlash_x86_WIN_100.00.02.03
- Fix -ACB do not check AC plugin issue.

Version 100.00.08.16
------------
COMMON
- Fix PFAT flash process.
- Show progress bar while flashing PFAT.
- Add Boot Guard feature.
- Update SecurityFlash package to 100.00.02.02.
- Update copyright to 2017.
- Update log feature.
- Enhance OEM complete action.
- Add ErrorPause in Platform.ini
WINDOWS
- Getting power status from different way in normal Windows and Windows PE.
DOS
- Fix SinglePackage with signed bin file cannot update issue.

Version 100.00.08.15
------------
COMMON
- Show progress while exporting BIOS region to file.
- Add Oem Complete Action feature.
- Add a fool-proofing for BIOS region check to prevent region map without END type.
DOS:
- Fix the error in reading whole rom map.

Version 100.00.08.14
------------
COMMON
- Add -SRC command to support skip region check.
- Show new build time as BCD(Binary-coded decimal) format.
- Show BIOS build datetime as N/A if it's all blank.
- The -sb command shows build datetime when it's not n/a as -sc command.
- Change the format of release note.
- Remove incorrect region check if input BIOS image size less than ROM size.
- Show more precise status message when failing to run secure flash.
- Update SecurityFlash package to 100.00.02.00

WINDOWS
- Fix secure flash via ESP failure in legacy mode.
- Only one H2OFFT exists at the same time.
LINUX
- Support secure flash via ESP (viaESP) in legacy mode.
- It's able to find more ESP if default path failed in UEFI mode.
DOS
- Support secure flash via ESP (viaESP).

Version 100.00.08.13
------------
1. Fix viaESP errors.
2. Windows: fix side-by-side configuration error for Windows PE.

Version 100.00.08.12
------------
1. Rename message_xxx.ini to msg_xxx.ini.
2. Change the default name of [Log_file] FileName to avoid long name error under DOS.
3. DOS: fix read BIOS image error in single package.
4. DOS: fix -sb error in single package.
5. Windows: get BIOS fd from single package.
6. Update FdPacker to version 100.00.03.08.

Version 100.00.08.11
------------
1. [GUI] Removed "Silent mode(for Console Mode)" option in option tab.
2. [GUI] Added [HoldGuiBeforeFlash] in platform.ini.
3. [GUI] Updated procedure to raise graphic interface.
4. Hid "Latest version" message for same version BIOS of ACER project.
5. Supported customized EC update block size.
6. Supported to report not predefined EC size.
7. Supported command "-eob" and platform.ini setting "BIOS_Only".
8. Supported Action_20h in [UpdateEC].
9. Supported Action_21h in [UpdateEC].
10. Show proper progress title while R/W blocks.
11. [Windows] [Log_file] Flag=1 in platform.ini can log FlsHookDll.dll in flshookdll.log.
12. Fixed [PasswordCheck] PasswordCheckEnable=1 in platform.ini check password failure.
13. Fixed L01 password check function.

Version 100.00.08.10
------------
1. [GUI] Fixed the issue that platform.ini will be emptied after change options.
2. [GUI] Fixed the File Name field in Option dialog can not show context properly after loading FD file name in platform.ini.
3. [GUI] Fixed the version is shown only 20 characters in confirmation dialog.
4. Fixed the issue that EFI Variables still exist after BIOS flashed.
5. [Linux] Load INI files from the directory where application is as default.
6. Fixed the issue that BIOS model and version read failed and show N/A.
7. [Linux] Stop showing "Cannot get DC-Plug info" if AC is connected.
8. [GUI] Check/uncheck "Current and new BIOS group box" to enable/disable "BIOS ID information" and "BIOS version information" checkboxes.
9. Power line is not connected will not stop flash process if batter check is on and batter is connected.

Version 100.00.08.09
------------
1. Support Flash Rom Part size to 128MB.
2. Secure flash support via ESP.
3. Support multiple language by message_XXX.ini.
4. [Windows] Single package (self-extracting and executing file) can extract FD file now.
5. [Windows] Update dll files.
6. Fix failure of comparing string type BIOS version.
7. Fix failure of [FlashSecureBIOSOverride] in platform.ini.

Version 100.00.08.08
------------
1. [Windows] Update FDPacker to 100.00.03.07.
2. Rename Read.me to README.text.
3. [Linux] Update driver.
4. Show correct BIOS region name while it does not have full access right.

Version 100.00.08.07
------------
1. Update -nv usage.
2. Remove -eob command.
3. Update flash sequence, let the BVDT block update at the end of flash process.
4. Add MessageString0BF in message.ini
5. Add settings in [ForceFlash], [UI], [FlashComplete] and [MULTI_FD] blocks in platform.ini
6. Fix Rom map change feature bug.
7. Support customized AC & DC warning messages.
8. When input FD file contains BIOS region only, and it does not set [Region] bios=1 or command -bios. AP can auto detect and recognize input file.
9. Fix DirectFlash error by specific varialbe assertion.
10. Remove warning message when loading command.ini failed.
11. Do not check AC adapter when the function is disabled by plarform.ini or input argument.
12. Support multiple same data type region.

Version 100.00.08.06
------------
1. Add iFdPacker files.
2. [Windows] Update drivers.
3. [Windows] Fix file brwosing error in Options dialog.
4. [Linux] Update driver for kernel 4.0+.
5. [windows] Fix crash issue while press OK&Apply button in Options dialog.
6. Fix backup rom option can not save file in Options dialog.

Version 100.00.08.05
------------
1. [Linux] Update driver.
2. Fix dump incorrect BIOS region data.

Version 100.00.08.04
------------
1. Show power status in warning type.
2. Show successfull message instead of warning message while loading platform.ini and message.ini.
3. Fix show message with warning type but default type before load message.ini.
4. Update message.ini with new type: INFO(3).
5. Show error message while loading command.ini failed.
6. Change initializing procedure to load driver first.
7. [Windows] Fix crash while INI files are missing.

Version 100.00.08.03
------------
1. Fix secure platform check.
2. Show power status once if needed.

Version 100.00.08.02
------------
1. Fix secure flash doesn't work.
2. Fix remove driver device at inproper time.

Version 100.00.08.01
------------
1. Fix [ReturnCodeDefinition] in platform.ini returns incorrect code.

Version 100.00.08.00
------------
1. Fix procedure error on embedded system.
2. Update drivers.

Version 100.00.07.21
------------
1. Add [FlatForceFlash] to command.ini which has the same function as "-FF".

Version 100.00.07.20
------------
1. Support -EP error pause command.

Version 100.00.07.19
------------
1. Support -FF command to do Force Flash.

Version 100.00.07.18
------------
1. Fix wrong image passed to BIOS when the input image is BIOS part only.

Version 100.00.07.17
------------
1. Add a minor delay to fix a Windows crash caused by a long duration of OEM flash.

Version 100.00.07.16
------------
1. no argument is put in following dialog, it will NOT allow any argument when using single package.

Version 100.00.07.15
------------
1. Fix the improper behavior caused by some variables being uninitialized.

Version 100.00.07.14
------------
1. Support OEM Optional Version String Feature.

Version 100.00.07.12
------------
1. Fix EC flash problems that stops flash in size check.

Version 100.00.07.11
------------
1. Add hook point to Dos/Linux.
2. Fix EC prompt message before flashing it.
3. Fix private region movement problem.

Version 100.00.07.09
------------
1. Add new feature that supports IHISI 0x1F hook point notification.

Version 100.00.07.08
------------
1. The bug is fixed ,that direct flash flag of command.ini has no effect.
2. The bug is fixed ,that PressOneKeyToContinue captures a wrong key.

Version 100.00.07.07
------------
1. Fix bugs about checking power status.

Version 100.00.07.06
------------
1. Add Build Date and Time feature
2. Fix CMOS Read/Write filename problem

Version 100.00.07.05
------------
1. Add "direct flash" feature to oem secure flash.

Version 100.00.07.04
------------
1. Bugs are fixed.

Version 100.00.07.03
------------
1. Fix the wrong register to store status in FlashComplete IHISI call.

Version 100.00.07.00
------------
1. Add "-df" to enable direct flash without reboot which supports secure and normal flash.

Version 100.00.05.05
------------
1. Fix objection of RBU images caused by incorrect CRC checksum calculation.

Version 100.00.05.04
------------
1. Add "-pass:" to enable to input administrator password.

Version 100.00.05.02
------------
1. Remove dependency of the updating OEM ME's enable flag on the ME flag of region.

Version 100.00.05.01
------------
1. Merge source code of "Update OEM ME".
2. Add "-ssb" to skip secure boot.

Version 100.00.05.00
------------
1. The names of executables are changed.
2. Renew flash complete (IHISI 16h) SMI call arguments.
3. Update warning message when the new image version is the same or older than the current platform.

Version 100.00.04.00
------------
1. NV Storage are protected again even with the argument "-all".

Version 100.00.03.00
------------
1. Fix InsydeFlash.exe's ">" redirection to a text file does not work.

Version 100.00.02.00
------------
1. Fix iFdPacker.exe crush when the path of the tool's folder is longer than 256.

Version 100.00.01.00
------------
1. Fix iFdPacker.exe failed in loding drivers that caused by drivers being renamed.
2. Add iFdPackerFileList.ini to iFdPacker.exe that store file names to be added to SFX.

Version 100.00.00.01
------------
1. Supports Platform Update Flash Area by Type Command. -SP:TYPE(HEX)
For Example : Update Variable Area (TYPE 02h) ==> -SP:02
              Update OEM DEFINE 1 Area (TYPE 51h) ==> -SP:51


Version 100.00.00.00
------------
1. Supports Reserve SMBIOS DATA command. -RA -Rx.
2. Support Display Current/Bios ID and Version. -SC -SB.
3. Support Update NV, Oem Data, Variable. -spn -spo -spv.
4. Support Quiet mode. -q.
5. Support do not check ROM ID. -X


Version 5.28
------------
1. Supports PFAT image flash on platform PFAT feature disable. (BIOS version required: SharkBay 03.72.37.0018)
2. Supports PFAT checksum verify.
3. Adding [UI] ConfirmInfoRDate to support showing release date on confirm dialog. (BIOS version required: 03.72.43)
4. Fix missing last section of platform.ini in ini overwrite feature.

Version 5.27
------------
1. Support PFAT image update. (BIOS version required: SharkBay 03.72.37.0018)
2. Fix -edt#@:"Value" command may fail issue.
3. Support ini override for secure capsule update.
4. Fix can't get secure capsule model name and version issue on Strawberry Mountain 05.02.34.
5. Upadte iFdPacker to v2.2.7
    5-1. Support packing multi FD for DOS package.
    5-2. Update the behavior of pack platform.ini for secure image for DOS and Shell package.
         (Don't disable platform.ini pack option when secure image detected for DOS and Shell package.)

Version 5.26
------------
1. Add command -edt#@:"Value" for update customize data (such as logo with signature) by IHISI.
    #: from 4 ~ C, @: F, S, W, DW (F means file, S means string, W means word value, DW means double word value)
2. Support compare model name method in [Multi-FD] section.
3. Fix the system hang issue that flashing secure image (include BIOS + EC) on normal platform it may hang after EC flash complete and before restart.
4. Upadte iFdPacker to v2.2.6
    4-1. Fix Message error of windows package run in DOS mode.
    4-2. Fix pack error in fd path with space.
    4-3. Fix help message error.

Version 5.25
------------
1. Update version check behavior for OEM. [For specific OEM/ODM]
2. Fix OEM flash image size error issue. [For specific OEM/ODM]

Version 5.24
------------
1. Support OEM message when flashing secure image on normal platform and normal image on secure platform. [For specific OEM/ODM]
2. Upadte iFdPacker to v2.2.5.
    2-1. Add platform.ini pcak option in UI for Windows package.
    2-2. Modify ini pack flag for command line.
    2-3. Disable platform.ini pack option when secure image detected for DOS and Shell package.
    2-4. Fix the parameter checking behavior for command line mode.

Version 5.23
------------
1. Add DisableSecureCapsuleFlash flag in [Others] section in platform.ini to enable/disable flash secure BIOS on normal platform.
2. Supports OEM secure flash behavior. [For specific OEM/ODM]
3. Add version check rule for OEM. (it must base on BIOS report.) [For specific OEM/ODM]
4. Fix CommonFlash will be disabled when using Multi-FD feature. [For specific OEM/ODM]
5. Update AT-p behavior. It does NOT check AT-p signature in plaform supported when flash EC only.

Version 5.22
------------
1. Fix can not update issue when input image is a secure capsule with BIOS and EC.
2. Fix showing "The secure BIOS is signed by older version of security flash." issue when flashing a normal image on secure platform.
3. Disable option button on secure flash mode.
4. Update AT-p behavior. It can allow to flash when enrolled. The function is enabled by BIOS and BIOS must report the Dtimer status in IHISI.
5. Add [UpdateOEMME] CheckVersion=3 setting, let it continue to flash when OEM ME update fail.

Version 5.21
------------
1. Support to flash a secure capsule on a normal platform by normal flash method.
2. Upadte iFdPacker to v2.2.4.
     2-1. Add auto save previous settings feature.
     2-2. Add shell single package support.
     2-3. Add command line support. (Use "iFdPacker -h" to see the usage.)

Version 5.20
------------
1. Update Intel ME flash tool and add a Command setting in platform.ini [UpdateOEMME] section for customizing command.
2. Fix the issue that NV storage area still be cleaned even BIOS already report the area information by IHISI 1Eh on secure boot support platform.

Version 5.19
------------
1. Fix cannot flash secure bios which pack with EC image and set [UpdateEC] Flag=1 in secure flash mode.
2. Fix flash complete call twice issue.
3. Add all console command support -option.
4. On the platform which supports secure boot feature, utility will not flash the NV storage area which reported in IHISI 1Eh.
5. Fix secure flash 16MB+EC image cannot flash issue.
6. Fix the issue that power saving set is changed after update BIOS with enabling to lock mouse and keyboard.
7. Fix private region is not protected when -pbi command is executing.

Version 5.18
------------
1. Add do nothing action for 48h. And add some command for secure flash action override. [FlashSecureBIOSOverride] Action=0 for S3, Action=1 for reboot, Action=2 for shutdown, Action=3 for do nothing.
2. Add EFI driver version check for secure BIOS flash.
3. Detect current platform support secure update or not. It only allow to update secure BIOS on secure platform.

Version 5.17
------------
1. Update OA function behavior to meet Microsoft new requirement.

Version 5.16
------------
1. Support "InsydeFlash.exe BIOSFile.bin" command.
2. Fix the issue that Windows flash can run with guest account after run once with administrator account.
3. Modify AT-p error message.
4. Remove flash by AP feature. And remove platform.ini [ApplicatonFlash] section.

Version 5.15
------------
1. Remove flash progress message console output when it's running in silent mode.
2. Update iFDPacker to v2.2.1. Support packing DOS & Windows flash utility in single package.
    I.e. the sinagle package can runs on DOS and Windows.

Version 5.14
------------
1. The setting always show "BatteryBound=20" after set "[AC_Adapter] BatteryBound=30" in User option mode.
2. Modify -pbi to support all protection type.
3. Update driver for new interface of secure capsule flash.

Version 5.13
------------
1. Update -nopause behavior for OEM.

Version 5.12
------------
1. Add BatteryNotConnect, BatteryCapacityNotEnough in platform.ini.
2. Support 16M bios in secure capsule flash mode.
3. Update AT-p check behavior in WinPE.

Version 5.11
------------
1. Fix can not get correct SMI port issue in VIA VX900 platform.
2. Reduce memory usage of driver in non-secure flash mode.
3. Revise OEM specific error message for profile update (-pbi:Type command).

Version 5.10
------------
1. Support OEM specific error message for profile update (-pbi:Type command).
2. Fix the region may not be protected when start address + size equal to 0x100000000 which overflow of DWORD size.

Version 5.09
------------
1. Add Insyde Secure BIOS identify.
2. Update message of running secure capsule flash fail(call 48h fail).

Version 5.08
------------
1. Add conditional data check by bios (45h) feature. Enable/Disable flag is CheckByBios of [Bios_Version_Check] section in platform.ini.
2. Add user define error message for conditional data check by bios feature. The message is defined in CheckByBiosErrorMessage of [Bios_Version_Check] section in platform.ini.
3. Enlarge file size limitation of non-share EC size from 64KB to 256KB with single block write method.
4. Modify the default value of Version in [Version] section from "00" to empty string. On main dialog, it will show "InsydeFlash V5.08" as default not "InsydeFlash V5.08.00".
5. Add admin password check in flash protected region feature (with -pbi:Type) for OEM.
6. Support specified size of flash rom. Such as 5M(1M+4M), 6M(2M+4M) flash rom.
7. In secure flash mode add re-boot/shutdown function for WinPE.

Version 5.07
------------
1. Update message string.
2. Fix the issue that [Bios_Version_Check] flag=2 and BIOS allow same version to flash, when flash the same version it will show error message "Warning: cannot check BIOS version.".

Version 5.06
------------
1. Add EC compare and verify feature. The settings in platform.ini [UpdateEC] section, EC_Compare, EC_Verify and EC_VerifyErrorRetry.
2. Support passing multi project name to BIOS in CommonFlash feature for OEM.
3. Fix Hook functions can't correctly work (include mouse, keyboard, power button, sleep button, lid closed) on Win7 environment
4. Update iFDPacker to v2.2.0.0

Version 5.05
------------
1. Update AP pass to BIOS structure in CommonFlash feature for OEM.
2. Reduce initial time which cause by searching BVDT of on board BIOS.

Version 5.04
------------
1. Support move private map feature.
2. Disable Power button, Sleep button, and Lid closed function during flashing (controlled by DisableMouseAndKeyboardInput flag)
3. Fix EC can't update issue when EC image size is bigger then 64KB.
4. Fix that run iFdPacker.exe and click the Add button, "Encountered an improper argument" error message will occur

Version 5.03
------------
1. Remove update logo feature.
2. Add -forcetype, -forceit, -nopause for OEM menufacture mode.
3. Add error message when protected region type not found with -pbi:Type.

Version 5.02
------------
1. Update AtpTimerInfo.dll from v3.0.0.18 to v3.0.0.20, fix the load driver fail issue in Windows XP.
2. Fix the issue that utility always shows the same version and won't flash when PermitFlashVersion is enabled and the value of SingleVersion is the same as on board BIOS version.
3. Update iFDPacker to v2.1.8.0, fix single package won't ask for administrator privilege in x64 OS issue.
4. Add profile flash support by command line "InsydeFlash profile.fv -pbi:Type". It can be used to update partial region base on protecting map.

Version 5.01
------------
1. Fix -wb issue that writing variable from file didn't actually write the data
    (the data field of the variable is empty after using -wb parameter).
2. Add to pass EC flash flag to BIOS by IHISI 19h.
3. Fix the issue that flash utility didn't pop up warning message and do flash directly in DC mode on WinPE.
4. Fix -forcetype not workable issue.

Version 5.00
------------
1. Update AtpTimerInfo.dll, AtpTimerInfoX64.dll.
2. Add return code for [CommonFlash] interface when there is an error occur in the interface.
3. Fix to flash partial image will fail.
4. If file name has "\/:*?"<>|",tool will change to "_" in BackupROM.
5. Fix the issue that update same version ME will show an error message but the message end with some unreadable characters.
6. Add multi ini support. It can support ini settings overwrite by adding ini file name in [MULTI_FD] section.
7. Fix cannot show SMI error dialog.
8. Update iFDPacker to v2.1.6.0.

Version 4.04
------------
1. Support customize error message in [UpdateExtraData] section.
2. Fix passing platform.ini to bios data error.

Version 4.03
------------
1. Add a command line parameter /noconfirm to disable confirm dialog. (This command must add as latest parameter.)
2. Modify Silent flag to match "-s" silent mode.
3. Update iFDPacker to v2.1.5.0. Fix v2.1.3.0 can't work in Windows 7 issue.

Version 4.02
------------
1. Fix the issue that InsydeFlash settings in "Option" and "Browse FD File" buttons won't effect until next launch.
2. Fix /cpf will load driver twice error.
3. Modify iFDPacker to package FlsHook.exe and FlsHook.dll.

Version 4.01
------------
1. Change sequence of id and size check function, and remove flag "Check_Before_ROM_Size".
2. Add to check extra data image and pop error message.
3. Fix cannot show confirm dialog in silent mode with "SilentWithDialog=2".
4. Fix cannot check bios size when image with header.
5. Add UI for silent mode normal flash process.
6. Fix do not show error when cannot found match file in multi-fd feature.
7. Fix the issue that AC power will be checked in UEFI flash when [CommonFlash] is removed.
8. Fix cannot show date in confirm dialog.
9. Support log status code to CMOS. The settings are in [Log_file] section with prefix CMOS_.
10. Fix the issue that USB mouse can work when flashing VBIOS region.
11. Fix will show <N/A> in new version edit.

Version 4.00
------------
1. Fix return code error issue when driver load fail.
2. Fix can't run EFI flash issue when [BIOSVersionFormat] BIOSVFEnable=1.

Version 3.99
------------
1. Modify warning message to "Do Not Remove the AC Power and Turn Off Computer During BIOS Flashing!" for OEM.
2. Modify definition of [Others] VerifyErrorRetry key from enable/disable retry to retry times.
3. Fix flash extra data with no data in image will error.
4. Fix show dialog with "DisableMouseAndKeyboardInput" will lock keyboard and mouse.
5. Don't check AC power in UEFI flash.
6. Allow same version flash in non-silent mode when [Bios_Version_Check] Flag=1 for OEM behavior.

Version 3.98
------------
1. Fix flash data size error in extra data feature.
2. Fix x64 common flash interface fail issue.

Version 3.97
------------
1. Fix UEFI flash will get error data with non-share EC update.
2. Fix that cannot flash BIOS after Intel ME update.
3. Support password check by BIOS feature (IHISI 43h).
4. Support flash by BIOS check feature (IHISI 44h).
5. Add new return error code in [ReturnErrorCode].
6. Fix 3D feature cannot flash VBIOS data.

Version 3.96
------------
1. Support show IHISI version.
2. Modify "UpdateExtraData" feature to support 3D panel.
3. Fix Windows PE cannot shutdown and reboot.
4. Fix the issues cause by Unicode feature.

Version 3.95
------------
1. Fix /ecp cannot get IHISI version from BIOS.
2. Modify to support flash EC only.
3. Extracting image size is incorrect for OEM feature.
4. Add a section [PermitFlashVersion] to support conditional process of BIOS update.
   When a serial bios from old to new is version A B C,
    the newest bios update package is version C,
    and version C only can update from version B.
   Then you can use this feature to warning user of version A on board to update to version B first.
5. Add EC_Path key of [UpdateEC] section to support update EC by inputed file path.
6. Fix bug: When CheckVersion=2 and the ME FW is the same, it will close intel tool and doesn't continue to update BIOS.
7. Fix bug: Set Platform_Check flag=1 and Bios_Version_Check flag=1 to platform.ini,
    when bios version check is pass and platform ID is different, then WinFlash will flash the bios.

Version 3.94
------------
1. Fix cannot flash DXE region when you set "DXE=1" in 32 bit OS.
2. Fix flash in silent mode with not SilentWithDialog=1 and ActionOverride=1 will
    return error return code.
3. Add "/ECP" feature to flash non-share EC only.
4. Modify AT-p feature.
5. Version check enhancement, add [BIOSVersionFormat] section in platfrom.ini.
6. Modify to flash ME before BIOS.

Version 3.93
------------
1. Fix "Reboot!" dialog can't popup after flash in command silent mode if set
    "SilentWithDialog=2, [FlashFlashComplete]Action=2, Dialog=1"
2. Fix will pop EC auto close dialog in silent mode with SilentWithDialog=1.
3. Fix will not passing ini to BIOS when run OEM1 special flash rule.
4. Add "ForceIHISIVersion" in "Others" section.

Version 3.92
------------
1. Add "ActionOverride" flag.
   Flash utility bases action key setting to do original behavior.
2. Fix /cpf cannot process issue.
3. Fix when flash extra data with "DisableMouseAndKeyboardInput=1" will show error.
4. Add a section [PlatformVersion] in platform.ini.
   When the Flag=1 and platform check enabled, it will display the version string
    list in this [PlatformVersion] section and use it to compare.
   The Version is pair with the PlatformName.
   For example: When the platform ID matches with PlatformName2, the Version2 will be used.

Version 3.91
------------
1. Add new action definition when EC update completely.
2. Fix cannot copy correct BIOS image with sign file to USB dangle in Window XP system.

Version 3.90
------------
1. Add 16M ROM support
2. Add feature to pass parameter setting in platform.ini to BIOS.
3. Fix incorrect dialog pop up that cause when AT-P function enable and bios update only.
4. Fix update non-share EC feature error.

Version 3.89
------------
1. Rename "ErrorRetryDelay" to "SMIErrorRetryDelay".
2. Rename "ErrorRetry" to "VerifyErrorRetry".
3. Fixed some situation will not return error code.
4. Update AtpTimerInfo.dll to 2.0.2.24.
5. Added silent mode return code and flash complete action.

Version 3.88
------------
1. Fixed some error return bugs.
2. Modify OEM special feature in silent mode with SilentWithDialog=1.
3. Updated 32bits AT-p component (AtpTimerInfo.dll).
4. Fix file path conver from unicode to ansi string will lose the non-English words issue.

Version 3.87
------------
1. Pure 64bits application support AT-p utility.
2. Added update extra data feature to update VBIOS.

Version 3.86
------------
1. Fix the issue that system will crash after flashing when Check_Before_ROM_Size = 1.

Version 3.85
------------
1. Added "AllowVersion" to support OEM1 EFI update feature.
2. Fixed flash non-share EC, EC cannot shutdown/Reboot. Update from 3.84.
3. Fix incorrect spelling in "The BIOS image is corrupted or does not contain the correct digital signature. The system BIOS will not be updated."

Version 3.84
------------
1. Added check platform ID for UEFI update.
2. Add new warning/error message for AC/DC and Platform/Version check.
   (OEM specified message requirement)
3. Fixed flash whole BIOS with non-share EC or only BIOS region will show file size may not match.

Version 3.83
------------
1. Fixed Can not flash only BIOS region and non-share EC.
2. Support up to 20 PlatformName in platform.ini.

Version 3.82
------------
1. Add /cpf command for copy file to specific partition and folder.

Version 3.81
------------
1. Fixed IHISI failed when run /g command then run InsydeFlash again.
2. Fixed can not run InsydeFlash from different folder.

Version 3.80
------------
1. Modify "CheckVersion". If set 2, tool will not show error and continue to flash
    when ME flash error is cause of same version and downgrade version.
2. Fixed flash only BIOS region with only BIOS region data will not show new version and check version.
3. Removed SMI error code in SMI error message.
4. Fixed flash bios failed with AT-p utility.
5. Fixed EC size error.

Version 3.79
------------
1. Added "ErrorRetryDelay" and "SMIErrorRetry" at section "Others" in "Pltform.ini".
2. Modify behavior of OEM special signed feature.
3. Added solution that tool cannot identify BIOS binary (single BIOS region) is AT-p or non-AT-p BIOS.
4. Fixed that finished updating single BIOS region cause fail with AT-P utility.
5. Fixed that execute tool casue fail on Windows XP.

Version 3.78
------------
1. Added Calpella ME feature.
   [UpdateOEMME]
   MEFileName=
   CheckVersion=0
2. Added option "/ecr" and "/ecw" to access extend CMOS.
3. Modified "UpdateME" to "UpdateOEMME" and run Calpella ME feature.
4. Modified behavior about AT-p feature in tool.
5. "BeforeRunToolDelayTime" will Delay before UI dispaly.

Version 3.77
------------
1. Fixed get IHISI version error.
2. Added "MPCIIO" in Multi-FD.
   You can input many "PCI" or "IO" to check, even if "PCI" and "IO".
   If all of them match, tool will get this file to flash.

Version 3.76
------------
1. Modify when flash EC, tool will check EC rom size before flash BIOS.
   This is depended on IHISI version.
   When IHISI is newer than 1.8.6, it will check before BIOS flash.
   If not, it will check after BIOS flash.
2. Fixed flash EC with BIOS will flash many times error.
4. Added "DelayBeforeFlash" to delay before flash.
5. Modify "BeforeFlashDelayTime" to "BeforeRunToolDelayTime".
6. Added some messages and modified behavior about AT-p feature in tool.
8. Modify confirm message.

Version 3.75
------------
1. Fixed tool will send wrong EC size to BIOS with non-share EC.
2. Extended the EC buffer size to 2M.
3. Support OEM special request about check RSA check sign feature.
4. Skip check platform name and version feature will confirm BIOS.
5. Modify when flash EC, tool will check EC rom size before flash BIOS.
6. Add Platform data region access feature.
7. Add Platform_Check = 3 and Bios_Version_Check = 2 will get BIOS setting.
8. Modify default value of Platform_Check, Bios_Version_Check and ALL.

Version 3.74
------------
1. Modify main dialog logo and string font.
2. Added tool and BIOS hand shaking feature.
   Tool send BIOS information that include tool and OS version by functoin 10h.
   Get the customer vendor ID in function 10h.

Version 3.73
------------
1. Fixed to use /base /size option will hang.
2. Fixed to erase variable by ini will hang.
3. Fixed when setting "flag=2" in the section name "PlatformCheck" will get new name when current
    platform name and new platform name are match.

Version 3.72
------------
1. Fixed tool will show "Winodws 7" when it can not load driver in Windows XP.
2. Fixed tool will wait when using silent mode with no AC plug in.
3. Fixed error message when binary file not with EC part in UpdateEC feature.
   Change show "Error:File may not have ME rom" to "Error:File may not have EC rom".
4. Fixed platform check get ID fail, when updateEC flag = 2.
5. Add "/base:" and "/size:" to input base and size when use "/g" to read BIOS.
6. Modify Silent mode behavier:
   When SilentWithDialog=0, Not show any dialog.
   When SilentWithDialog=1, Show main dialog only.
   When SilentWithDialog=2, Show all dialogs without main dialog.
7. When SilentWithDialog=1 and run in silent mode, tool will check same version and not flash.
   (This Silent mode is mean use "-s" in command line)

Version 3.71
------------
1. Add "/lg:" to input the GUID.

Version 3.70
------------
1. Fixed the situation that tool will hang in XP on some platforms.

Version 3.69
------------
1. Modify Me flash feature.
   Support separate ME binary, and two type of Me:
   1. FULL SKU.
   2. Ignition SKU.

Version 3.67
------------
1. Add "/cr" and "/cw" to access CMOS in console mode.
2. Fixed some error word in status message when option flag set.

Version 3.66
------------
1. Add flash Me feature.
2. Fixed message from "If you are running this utility in Vista" to
    "If you are running this utility in Windows 7" for Windows 7 system.

Version 3.65
------------
1. Do not show dialog with "-s".
2. Fixed the problem can not get the return code.
3. Add flag "SilentWithDialog".

Version 3.64
------------
1. Modify the EC shutdown and reboot to get the "Action" in "FlashComplete".
2. Change "flag" in "Platform_Check". If flag=1 compare new rom platform name
    and current platform, else if flag=2 get the below names to compare.

Version 3.63
------------
1. Add "Progress_Bar" in ini file: Flash EC with draw progress bar.

Version 3.62
------------
1. Add "BIOS_Only" in ini file: Only flash BIOS when EC and bios are merge in the same file.

Version 3.61
------------
1. Before update EC after flash bios show dialog, change status and add flag "EC_Dialog=0" in ini file.
2. Fixed when tool flash on Calpella, the SMI will fail sometimes.

Version 3.60
------------
1. Expand EC buffer to 0x100000.

Version 3.59
------------
1. Fixed can not flash when rom file with platform region.

Version 3.58
------------
1. Fix the tool cound not run in UEFI OS (GPT format).

Version 3.57
------------
1. 8M support.
2. Fixed the error message when you flash same bios.
3. Fixed UpdateBlock feature about coundn't flash if physical address small than 0xFFF00000.
4. Fixed the processbar action problem, sometimes cound not process.

Version 3.56
------------
1. Fix BVDT Protect when the move region size smaller than 0x1000.

Version 3.55
------------
1. Fix BVDT protect function.

Version 3.54
------------
1. Fix some bug and some dialog string.
2. Modify backup rules.

   [BackupROM]
   Flag=0
   FilePath=
   FileName=

   Flag 1   -> Backup current BIOS and new BIOS binary
   FilePath -> If user does not enter the file path, utility will use current directory.
   FileName -> If user does not enter the file name, utility will use platform ID.
   xxx.xxx = Current BIOS image
   xxx_01.xxx = Previous BIOS image
   xxx_new.xxx = New BIOS image

Version 3.53
------------
1. Fix a bug in FlashTester.
   Counter is not correct.
2. Add mew BVDT protect function
3. Modify "Error:No FD match in INI settings." to "It is not for your notebook."

Version 3.52
------------
1. Add new key in INI setting.
   The "Disable read" function in DOS Flashit will skip "Compare" and "Verify" steps.
   In INI file, "DisableCompare" only skip "Compare" step.
   However, some OEM/ODM projects can not read binary from flash part.
   Windows version add "DisableVerify" key in INI, It will disable "Verify" step if this key is 1.
2. Add BIOS binary selection in INI file.

   [MULTI_FD]
   Flag=1
   FD#01=PCI,0,1F,2,80,7006,7007,9.fd
   FD#02=PCI,2,0,0,4,100006,100007,7.fd
   FD#03=PCI,2,0,0,18,0c,0e,9.fd
   FD#04=PCI,0,1f,0,0,0015808F,2815808F,8.fd
   FD#05=IO,C0,5AABFE02,5AABFE02,9.fd
   FD#06=IO,1F6,E7,E4,7.fd
   FD#07=IO,C0,fe03,fe03,7.fd
   FD#08=IO,C0,03,01,7.fd
   FD#09=PCI,2,0,0,0,813,812,9.fd

   Flag 1 -> Multi-FD mode, 0 -> normal mode
   FD#XX support 99 files FD#01 ~ FD#99
   FD#XX=IO Type,Offset,Mask,Value,File name
   FD#XX=PCI Type,Bus,Device,Function,Offset,Mask,Value,File name
   Type -> Support IO space and PCI address type
   Offset -> Offset (HEX)
   Mask -> IO type support BYTE, WORD, DWORD (HEX). For example, BYTE -> 03, WORD -> 0A01, DWORD 100400D3
        -> PCI type support DWORD only
   File name -> File name of FD
   If [Offset] & Mask == Value, then flash the following file.

3. Support Windows PE 2.0 x64 version.
   User must run InsydeFlashx64.exe in x64 PE.
   The user can make pure x64 InsydeFlash in FD Packer.
4. Support FD argument.
   For example: Run InsydeFlash.exe xxx.fd
   It will skip MULTI_FD in INI and auto-searching FD.
5. Support /g argument.
   For example: Run InsydeFlash.exe xxx.fd /g
   Just like DOS version, user can read current ROM to a file.
6. Verify regions (descriptor mode) in ROM file.

Version 3.48
------------
1. When user enable UAC in Vista, the user need to "Run as administrator" with InsydeFlash.
   Now, InsydeFlash will notice Vista. Vista will pop up message box.
2. Fix unstable place when InsydeFlash is initializing.

Version 3.47
------------
1. Change InsydeFlash behavior.
   OLD: Even AC flag is 1, AC adapter does not plugged but battery life percent is fine. InsydeFlash allow flash process.
   NEW: If AC flag is 1, AC adapter should be plugged.

Version 3.46
------------
1. Fix a battery detection bug.
   InsydeFlash will get current battery life percent value from OS and compare with value in platform.ini.

   [AC_Adapter]
   BatteryCheck=1
   BatteryBound=20

   Also, if battery life percent is not enough, it will display the value in message box.

Version 3.45
------------
1. In platform.ini, InsydeFlash add more keys for model checking process.

   For example, ODM may have one BIOS for different model.
   They need to use different ID in different model.

   There are two kinds of solutions.
   First, user add ID list in ini file. User set Flag to 2.

   [Platform_Check]
   flag=2
   PlatformName=AAA1
   PlatformName2=AAA2
   PlatformName3=AAA3
   PlatformName4=AAA4
   PlatformName5=AAA5
   PlatformName6=AAA6
   PlatformName7=
   PlatformName8=
   PlatformName9=

   Second, ODM reports all IDs in one string at IHISI function 11h and BVDT.
   For example, the string will be like "AAA1AAA2AAA3AAA4AAA5AAA6".
   Also, some share ROM model need check EC's id, ODM can combine the ID with this string.

2. iFdPacker version 2.0.5
   The single execution file's icon change to official Insyde icon.

Version 3.44
------------
1. Platform.ini add [VARIABLE] to erase variable.

Version 3.43
------------
1. Fix flash after platform can not boot to OS.

Version 3.42
------------
1. Confirm dialog always on top.

Version 3.41
------------
1. Fix fail issue that user press start button.

Version 3.40
------------
1. Add a GET FD file button.
   [UI]
   GetFDFileButton=0

Version 3.39
------------
1. Add a wrong mesage box.

Version 3.38
------------
1. Add when error message occur, unlock keyboard and mouse.
2. Fix PlatformName by ini display error.

Version 3.37
------------
1. Fix "Alone Flash Region binary file" function can not flash EC.
2. Fix "Alone Flash Region binary file" function flash protect area issue.

Version 3.36
------------
1. Fix "Alone Flash Region binary file" function issue.

Version 3.35
------------
1. Add "Alone Flash Region binary file" function.
2. Modify "write HDCP key" function read file rule.

Version 3.34
------------
1. Remove program window (X) button.
2. Add Retry checking AC power function.
3. Modify some wrong message.
4. Add on flashing playing wav file.
5. Support IHISI function 19h.
6. Lock all input without system key ("CTRL+ALT+DEL").
7. Add check platform name by .INI function.
8. Add return code set by .INI.
9. Add a new argument(/WH) for "write HDCP key function".
10. Support IHISI 1.7.4 (OEM/ODM customization-2).

Version 3.33
------------
1. Fix driver bug.
2. Add /EV arguments.

Version 3.32
------------
1. Add Disable read compare by IHISI (function 11h).
2. Add new Variable (SLP2M & SLP2P).
3. Add support IHISI spec 1.7.1 new feature.
4. Add Disable model name & Version display by IHISI (function 11h).

Version 3.31
------------
1. Add Display Wrong message on Dialog "Do not turn off your computer".

Version 3.30
------------
1. Support R3.5 code base for "patch logo function".

Version 3.29
------------
1. Add Region map arguments (BIOS, GbE, ME, DESC).

Version 3.28
------------
1. Add DLL_AP_FlashComplete function.
2. Add ICL50_M005_TURN_OFF_DTS.
3. Add APTURN_OFF_DTS.
4. Add AP_Read_Memory_Buffer.

Version 3.27
------------
1. Add error code configuration.
2. Add silent style in console mode (-s).

Version 3.26
------------
1. Add application flash (64bit).

Version 3.25
------------
1. Fix 64bit driver bug.

Version 3.24
------------
1. Add application flash (32bit).

Version 3.23
------------
1. Fix driver bug.
2. Add retry function.
3. Add read compare switch.

Version 3.22
------------
1. Add error return code.
2. Support binary variable access.

Version 3.21
------------
1. Add /C arguments

Version 3.20
------------
1. Add UI configurations.

Version 3.19
------------
1. Dynamic find IHISI main function number.
2. Add UI configurations.

Version 3.18
------------
1. Add BVDT.
2. Add ID display.

Version 3.17
------------
1. Fix buffer overflow bug.

Version 3.16
------------
1. Modify iFdPacker function.

Version 3.15
------------
1. Add /1 /2 /4 /8 arguments.

Version 3.14
------------
1. Add command line argument for iFdPacker.
2. Add FV ID protection.

Version 3.13
------------
1. Support BIOS IHISI 1.6.2.
2. Add log file argument.

Version 3.12
------------
1. Add command line arguments.

Version 3.11
------------
1. Fix UI block problem.

Version 3.10
------------
1. Add silent mode.
2. Add tool: InsydeFdPacker.

Version 3.06
------------
1. Add a key in INI for turn on/off end dialog.
2. Fix file not found bug.

Version 3.05
------------
1. Support BIOS IHISI 1.5.8.
2. Add FV update mode.

Version 3.04
------------
1. Support BIOS IHISI 1.5.7.

Version 3.03
------------
1. Support BIOS IHISI 1.5.6.

Version 3.02
------------
1. Supprt BIOS IHISI 1.5.5.
2. Utility can covert logo image.
